千泰塑膠長期供應(TPE)TF4AAD∕158-1846-5693經理：周生0769-3321-4396 QQ:275-158-775(千泰塑膠)貨源穩(wěn)定，價格優(yōu)惠，質量保證，歡迎來電咨詢，提供SGS報告，出廠認證，MSGD,COA,UL黃卡等資料….(TPE)TF4AAD∕Long term supply PMMA the folding principle of organic glass, English: (Polymethylmethacrylate), abbreviated as: PMMA; chemical name of organic glass is called PMMA polymer compound by methyl acrylate polymerization into. Smooth surface, bright color, the proportion of small, high strength, corrosion resistance, moisture resistance, light fastness, good insulation, good sound insulation. It can be classified into three types: shape material, rod shape material and plate shape material. The polymers obtained by polymerization of acrylic acid and its esters are collectively referred to as acrylic acid esters, and the corresponding plastics are called polyacrylic acids. Among them, Zui is widely used. PMMA abbreviation code named PMMA, commonly known as a transparent organic glass, excellent performance, through more than 92% of the sun light, ultraviolet rays up to 73.5%; according to the shape can be divided into four kinds of the types of organic glass folding. Colorless transparent organic glass is Zui common, the use of Zui large organic glass materials. Colored transparent organic glass: commonly known as color board. Light and soft, with it made of light boxes, crafts, people feel comfortable and generous. PPO polyphenylene oxide (PPO), also known as polyphenylene ether B, is one of the world's five major engineering plastics. Chinese PPO aka B Plastics Polyphenylene ether features large rigidity, high heat resistance, flame resistance, the advantages of non-toxic, pollution resistant property table directory 1 PPS polyphenylene ether (PPO) Chinese name called polyphenylene ether B, is one of the world's top five general-purpose engineering plastics. The utility model has the advantages of high rigidity, high heat resistance, flame resistance, high strength, good electrical performance, etc.. In addition, the wear resistance and electrical properties are better. PA11 and the mass ratio of 70: 30, the viscosity of the blend was about of pure PA11, and the rheological properties of the blends were stable. Considering the processing and impact properties, the mechanical properties of PA11 and PA1010 with a mass ratio of 70: 30 were better than that of pure PA11, and the cost was significantly lower than that of pure PA11. With the modified PA6 blend due to the molecular structure of PA6 with strong polarity, the water absorption rate, easy to cause a decrease in strength and modulus, impact toughness and dimensional stability of PA6 under the condition of low temperature and low. Through the blending of PA11 and PA6, the blends have good mechanical properties and reduce the price of PA11. The relationship between the amount of compatibilizer and the mechanical properties of PA11/PA6 blends was studied by using PA6 and PA11 copolymer as compatibilizer. The results show that the addition of compatibilizer, the elongation of PA11/PA6 blends were improved obviously, 75: 15: 5: 5, the tensile strength can be increased from 2% to 5%, the impact strength of pure PA11 2 ~ 8 times, the cost can be reduced by more than 20%, is a very broad application prospects of super tough PA11 alloy material. PPS type glass fiber reinforced model D2 features high toughness fiber content GF20 physical properties test method unit density G/cm3ISO11831.56 water absorption rate of shrinkage of%ISO620.02 parallel 0.35%% 0.65 vertical mechanical properties tensile strength MpaISO527160 elongation MpaISO5271.75 flexural strength flexural modulus of MpaISO178185 compressive strength MpaISO17812000 MpaISO178145 notched impact strength of KJ/m2ISO18020 electrical properties of volume resistivity of Omega.MIEC600931.2 * 1015 surface resistance IEC600932 * 1015 1MHzIEC602503 dielectric loss factor 1MHzIEC602500.002 electrical strength KV/ mmIEC6024317 tracking index V IEC60112100 heat resistance thermal deformation temperature of IOS75-2255 flame retardant UL94V0 injection drying temperature of 140 DEG C for 4 hours of injection temperature of 290 and 330 C and 150 C 120 mold temperature injection speed moderate pressure 50 - 90Pa[2] PPS engineering plastics processing method of processing characteristics of resin manufacturers to provide a relatively low quality (4000~5000), a high degree of crystallinity (75%) of the white powder, the pure PPS can not directly plasticizing molding, can only be used for spraying. LCP injection pressure and injection speed Zui suitable injection pressure must depend on the material, product shape, mold design (especially the sprue, runner, gate) and other molding conditions. However, LCP has no grade and its melt viscosity is very low, so the injection pressure is lower than that of the general thermoplastic resin. It is a good way to form a low pressure at the beginning, and then slowly increase the pressure. Almost all of the molding products can be formed under the injection pressure of 15MPa-45MPa. In addition, the curing time of LCP is faster, so it is easy to get good results.